Big Easy Flooring, New Orleans
Flooring Advice

Refinishing Original Hardwood in a New Orleans Historic Home

Worn wood strip floor in a sunlit dining room with a wooden table and chairs

An original floor in an older New Orleans house has already lived through decades of humid summers, earlier sandings, and coats of finish nobody wrote down. Under all of that may be old-growth heart pine that cannot be bought new. Refinishing it well starts with knowing how much of that wood is left.

At Big Easy Flooring, we sand, refinish, and repair hardwood floors across New Orleans, including floors we did not install. On an older house, that work usually means saving what is already there.

Refinishing the original floor in a historic home is a different job from sanding a floor laid ten years ago. The boards are older, the finish history is unknown, and every pass of the sander removes wood that cannot be replaced like for like.

If your original floor looks tired and you want to know whether it can take another sanding, contact us and we will come out to measure it.

This post covers what makes an original floor different, what gets in the way of refinishing it here, the signs it needs more than a fresh coat, and how the work is assessed and done.

What an Original Heart Pine Floor Means in a New Orleans Home

Heart pine is the dense, resinous heartwood of old pine trees, and the name is most often tied to longleaf. For refinishing, that matters for one reason. The wood in an original floor is a resource with a fixed supply.

Heartwood From Old-Growth Longleaf Pine

Close-up of aged dark wood floorboards with visible grainAccording to the Southern Pine Inspection Bureau, lumber cut from the heartwood of any Southern Pine species can be called heart pine. Longleaf is the species the trade most often means by the name. Longleaf is known for tight growth rings, high density, and a large share of heartwood.

The resin is part of what you are paying attention to. One restoration crew told Hardwood Floors magazine that the resin creates the wood’s color, density, and rot resistance. It is also why old heart pine looks the way it does after a fresh finish.

A Supply That Is Not Coming Back

A USDA Forest Service paper estimates that longleaf pine once covered about 90 million acres of the Southeast. Longleaf forests now exist on less than 3 percent of that range. Old-growth stands cover less than 9,900 acres, about 0.01 percent of what once stood.

Replacement heart pine today comes from salvage. Woodworkers Journal describes it as lumber recovered from houses, warehouses, and other old buildings that are taken down. Once an original board is sanded through, the only match for it is another old board from somewhere else.

Every Sanding Takes Something Away

A traditional sanding removes 1/32 to 1/16 inch of wood from the surface, according to Hardwood Floors magazine. Most solid floors can take six to eight sandings over their service life.

A floor that has been in a house for generations may have used some of those already. The real question before any refinish is how many are left, and that answer comes from a measurement, not from how the floor looks.

Why Old Floors Are Harder to Refinish Here

An old floor brings its own history to the job. A New Orleans house adds its climate, its building type, and sometimes its paint on top of that.

Dense, Resinous, and Brittle Wood

Antique heart pine is dense and brittle because of its age and resin content, according to the crew that restored a century-old heart pine courthouse floor for a Hardwood Floors magazine feature. Their advice was blunt: you cannot get too aggressive with it.

A heavy-handed sanding can chip board edges and take more wood than an old floor can spare. That is why sanding heart pine calls for a careful hand.

Wax and Unknown Finishes on the Surface

An original floor may carry layers of wax, polish, or finish from earlier refinishes, and nobody may know which products were used. Hardwood Floors magazine warns that wax left in the seams and soft grain of a floor can keep a new finish from bonding.

A floor with a wax history has two realistic paths. It can stay a wax floor and be rewaxed, or it can be sanded to clean bare wood before a modern finish goes on.

Humidity Under a Raised House

If your house sits on piers, the floor is sitting over a crawl space. An LSU AgCenter study looked at raised houses in New Orleans and Baton Rouge. The AgCenter’s housing specialist said the water table in Louisiana is so high, and so many raised houses sit in flood zones, that the sealed crawl space system recommended in other areas is risky here. The same release notes that high humidity can cause decay in floors.

Cupping, where board edges rise above the center, almost always points to moisture coming from underneath. On a raised house that usually means the crawl space. Our post on moisture testing before new flooring explains how that moisture is measured, and the source needs attention before any sanding is scheduled.

Painted Surfaces in a House Built Before 1978

Paint can show up on an old floor as a painted border or old drips, and on the baseboards that sit against it. The EPA’s Renovation, Repair and Painting rule covers anyone paid to do work that disturbs painted surfaces in homes built before 1978, and the firm doing that work must be certified.

If any part of your floor or trim carries old paint, bring it up before the work is scheduled so it can be planned for.

Signs an Original Floor Needs More Than a Fresh Coat

A floor that is only dull can sometimes be renewed with a recoat, which adds a new topcoat over the existing finish without sanding to bare wood. The signs below point to a full refinish, repair work, or both.

Finish Worn Through to Bare Wood

Bare wood showing in the traffic lanes at doorways, hallways, and in front of the kitchen sink means the finish has worn through. Hardwood Floors magazine notes that a recoat suits floors without deep gouges where the finish has not completely worn through.

Once bare wood shows, the floor needs to be sanded. A worn lane is a floor asking to be refinished, and catching it early keeps the job smaller.

Cupped, Crowned, or Lifting Boards

Boards with raised edges, raised centers, or ends that lift underfoot are telling you about moisture before they tell you anything about the finish. Sanding them flat while the moisture is still there does not solve the problem underneath.

If the floor took on water in a storm, our guide on what to do when flood water reaches your floors covers the first steps before any refinishing is discussed.

Nail Heads at or Above the Surface

Old floors can have nail heads sitting flush with the surface or standing slightly proud of it. Before power sanding an old floor, the Old Farmer’s Almanac advises setting every protruding nail head below the surface with a hammer and nail set. The Almanac’s reason is practical: a raised nail head tears the sandpaper.

Damaged, Missing, or Patched Boards

Hands drilling into a wooden board with weathered planks in the backgroundBoards that are split, rotted, burned, or patched with a different wood need attention before the floor is sanded. A refinish goes over whatever is there, so repairs come first.

Holes left by old floor registers and boards cut for long-gone plumbing fall into the same group. Each one is a spot where a matched board has to be found and fitted before the sander comes out.

How an Original Floor Is Assessed and Refinished

The work runs in a fixed order: measure, repair, sand, finish. Each step depends on the one before it.

Measuring How Much Wood Is Left

An old floor wears unevenly, so a single reading near a doorway says little about the room. Hardwood Floors magazine recommends checking wear layer thickness in several areas to get a real picture of the floor.

On our hardwood floor refinishing and repair jobs, we measure that on site and do not guess, because sanding a board that is already thin ruins it. If boards have been sanded down too far, replacing that section is the honest answer.

Repairing Boards Before Sanding

Damaged boards are cut out and replaced, loose boards are secured, and protruding nails are set. For heart pine, replacement boards come from salvaged lumber.

In the courthouse restoration Hardwood Floors magazine covered, the crew matched the floor with wood reclaimed from an old home. They noted that the age of the tree matters more than the age of the building the wood came from. Because the grading rules set no heartwood ratio that defines heart pine, it also pays to know where salvaged boards were sourced.

Sanding With a Light Hand

On an uneven old floor, sanding everything flat to the lowest board costs the thicker boards wood they did not need to lose. The courthouse crew grouped boards of similar thickness and sanded them to preserve the wear layer.

The goal is a sound, clean surface that keeps as much original wood as possible. A floor that keeps its age marks is a floor that still has sandings left.

Choosing a Finish for Heart Pine

Oil-based polyurethane leaves an amber glow and usually needs 2 to 3 coats, though its strong odor can linger for a few days. Water-based polyurethane dries clear, does not yellow, and has a low odor, but generally takes about 4 coats.

On the courthouse floor, the architect chose an oil-modified polyurethane to recreate the look of traditional varnish. The right finish for your floor depends on the color you want to keep.

Method What It Involves Best For
Recoat Abrading the existing finish and applying a new topcoat, with no sanding to bare wood Sound, unwaxed floors that are dull but not worn through
Full sand and refinish Sanding to bare wood, then building a new finish Worn-through lanes, a wax history, or deep scratches, with enough wood left to sand
Board repair plus refinish Replacing damaged boards with matched salvaged wood, then sanding and finishing the whole floor Burns, rot, register holes, or mismatched patches in an otherwise sound floor
Section replacement Removing and relaying boards that cannot be saved Areas sanded down too far, rotted, or cupped by long-term moisture

What This Means for Your New Orleans Home

An original floor is worth checking before anyone decides it has to go. If there is enough wood left, refinishing is usually the better value, and boards past saving can be repaired with matched wood.

The order matters more than the speed. Deal with any moisture problem first, measure the wood that remains, repair what needs it, and only then sand and choose a finish.

At Big Easy Flooring, we measure original floors on site and tell you plainly whether you are looking at a refinish, a repair, or a replacement. The on-site measure is free and comes with a written quote.

To book a free measure for your original floor in New Orleans, call us today at (504) 305-8727.

Frequently Asked Questions

Can original heart pine floors be refinished?

Yes, as long as enough wood remains to take another sanding. Heart pine is dense and brittle with age, so it calls for a lighter hand than a newer floor. Damaged boards can be replaced with salvaged heart pine before the floor is sanded.

How many times can a solid wood floor be sanded?

Most solid wood floors can be sanded six to eight times over their service life, according to Hardwood Floors magazine. Each traditional sanding removes 1/32 to 1/16 inch. An old floor may have used several of those already, so the remaining thickness has to be measured, not assumed.

Do I need HDLC approval to refinish floors in a historic district?

The City of New Orleans says a Certificate of Appropriateness from the Historic District Landmarks Commission is required for exterior work on buildings in local historic districts and on designated landmarks. If your house is in a historic district or is a designated landmark, check with the HDLC before work starts.

What is the difference between a recoat and a full refinish?

A recoat adds a fresh topcoat over the existing finish after it is abraded, without sanding to bare wood. A full refinish sands the floor down to bare wood and starts the finish over. A recoat only suits a floor whose finish has not worn through and that has no wax on it.

How can I tell if my old floor has been waxed?

Hardwood Floors magazine describes two simple tests. Rub a white rag dampened with mineral spirits on the floor, and a yellow or brown stain suggests paste wax. Or set a few drops of water on the floor, and white spots after about 10 minutes suggest a wax finish. Test in the main part of the room, not in a closet or under a rug.

Should heart pine get an oil-based or water-based finish?

It depends on the color you want. Oil-based polyurethane adds an amber glow and needs fewer coats, while water-based dries clear and does not yellow. For a look close to traditional varnish, one historic restoration used an oil-modified polyurethane.

Can damaged heart pine boards be matched?

Yes, with salvaged lumber, since old-growth longleaf is now rare. Reclaimed heart pine comes from old houses, warehouses, and other buildings that are taken down. When matching, the age of the tree matters more than the age of the building, so ask where replacement boards were sourced.

Does lead paint matter when refinishing an old floor?

It can. The EPA’s Renovation, Repair and Painting rule covers anyone paid to do work that disturbs painted surfaces in homes built before 1978, and the firm must be certified. If your floor has a painted border, or the baseboards will be disturbed, raise it before the work is scheduled.



Keep Reading

More From the Blog

Free Estimate

Talk It Through With Us

A free on-site measure, a written quote, and a straight answer about what suits the room. Monday to Friday, 8 AM to 6 PM.

Call (504) 305-8727Send us the details

Free estimate
Get a free estimate
Free Estimate

Tell Us About the Floor

Fill this in and we will be in touch to book the free on-site measure. Rather talk? Call (504) 305-8727.